Cisco 350-501 Cert Guide PDF 100% Cover Real Exam Questions
Pass 350-501 Exam - Real Questions and Answers
NEW QUESTION # 156
Drag and drop the multicast concepts from the left onto the correct descriptions on the right.
Answer:
Explanation:
NEW QUESTION # 157
Refer to the exhibit:
Which effect of this configuration is true?
- A. R1 can support a graceful restart operation on the peer, even if graceful restart is disabled on the peer
- B. R1 can support a peer that is configured for LDP SSO/NSF as the peer recovers from an outage
- C. R1 can failover only to a peer that is configured for LDP SSO/NSF
- D. R1 can failover to any peer
Answer: C
NEW QUESTION # 158 
Refer to the exhibit. Router 1 was experiencing a DDoS attack that was traced to interface gigabitethernet0/1.
Which statement about this configuration is true?
- A. Router 1 drops all traffic that ingresses interface gigabitethernet0/1 that has a FIB entry that exits a different interface.
- B. Router 1 accepts source addresses that have a match in the FIB that indicates it is reachable through a real interface.
- C. Router 1 accepts all traffic that ingresses and egresses interface gigabitethernet0/1.
- D. Router 1 accepts source addresses on interface gigabitethernet0/1 that are private addresses.
Answer: B
Explanation:
Section: Architecture
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/4_1/nx-os/security/configuration/ guide/sec_nx-os-cfg/sec_urpf.html
NEW QUESTION # 159
Refer to the exhibit:
A network engineer is implementing an OSPF configuration Based on the output, which statement is true?
- A. OSPFv3 does not run for IPv4 on FastEthemet0/0 until IPv6 routing is enabled on the router and IPv6 is enabled on interface Fastfc.thernet0/0
- B. OSPFv3 cannot be configured for IPv4; OSPFv3 works only for IPv6.
- C. In the ospfv3 1 area 1 ipv4 command, area 0 must be configured instead of area 1.
- D. IPv6 routing not enabled" is just an informational message and OSPFv3 runs for IPv4 on interface FastEthernet0/0 anyway
Answer: A
NEW QUESTION # 160
An engineer is implementing MPLS to monitor within the MPLS domain. Which must the engineer perform to prevent packets from being forwarded beyond the service provider domain when the LSP is down?
- A. Option A
- B. Option B
- C. Option C
- D. Option D
Answer: B
NEW QUESTION # 161
Refer to the exhibit.
A network administrator is implementing IGMP to enable multicast feed transmission to the receiver. Which configuration must the administrator deploy on GW1 to permit IGMP Joins only to the assigned (S, G) feed?
- A.
- B.
- C.
- D.
Answer: C
Explanation:
NEW QUESTION # 162 
Refer to the exhibit. If the NetFlow configuration is updated to version 9, which additional piece of information can be reported?
- A. IPv6 flow information
- B. IPv4 flow information
- C. BGP AS information
- D. flow sequence numbers
Answer: A
Explanation:
Section: Automation and Assurance
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipv6/configuration/12-2sx/ipv6-12-2sx-book/ip6- netflow.html
NEW QUESTION # 163
Refer to the exhibit.
An engineer configured BGP summarization on a customer's network. Which route is advertised to BGP peers?
- A. 192.168.1.0/24
- B. 192168.0.0/16
- C. 192.0.0.0/16
- D. 192168.0.5/30
Answer: B
NEW QUESTION # 164
Refer to the exhibit. A network operator working for a private telecommunication company with an employee id: 7138: 13:414 just added new users to the network, which resides in VLANs connected to routers R1 and R4. The engineer now must configure the network so that routers R1 and R4 share routes to the VLANs, but routers R2 and R3 are prevented from including the routes in their routing tables. Which configuration must the engineer apply to R4 to begin implementing the request?
- A. pseudowire-class ciscotest
encapsulation mpls
service-policy output ciscotest - B. pseudowire -class ciscotest
encapsulation mpls
interface gigabitethernet 1/0/1
connect neighbor 192.168.1.1 101 pw-class cisco - C. interface serial 2/0/0
frame-relay encapsulation
ip address 192.168.1.4 255.255.255.0
service-policy output ciscotest - D. pseudowire -class ciscotest
encapsulation mpls
interface gigabitethernet 1/0/1
xconnect 192.168.1.1 101 pw-class ciscotest
Answer: D
NEW QUESTION # 165
After a possible security breach, the network administrator of an ISP must verify the times that several different users logged into the network. Which command must the administrator enter to display the login time of each user that activated a session?
- A. show platform software yang-management process
- B. show netconf-yang datastores
- C. show netconf-yang sessions detail
- D. show netconf-yang sessions
Answer: C
Explanation:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/prog/configuration/167/b_167_programmability_cg/configuring_yang_datamodel.html
NEW QUESTION # 166
Refer to the exhibit.
While troubleshooting a connectivity issue on router R2, a network engineer with an employee id:3876.13.497 notices that although it detects three OSPF links from R1, the OSPF prefixes are missing from the routing table. What is the reason for the problem?
- A. The R2 Serial 1/0 interface is configured with an IP address, but the R1 Serial R1 Serial 1/0 interface in unnumbered.
- B. Both loopback interfaces on R1 are configured as stub
- C. The serial interfaces have different MTUs
- D. The subnet masks on the serial interfaces are mismatched.
Answer: A
NEW QUESTION # 167
Refer to the exhibit.
Router R1 is reporting that its BGP neighbor adjacency to router R2 is down, but its state is Active as shown. Which configuration must be applied to routers R1 and R2 to fix the problem?
A)
B)
C)
D)
- A. Option B
- B. Option A
- C. Option C
- D. Option D
Answer: C
NEW QUESTION # 168
Refer to the exhibit:
R1 and R2 are directly connected with Fast Ethernet interfaces and have the above configuration applied OSPF adjacency is not formed. When the debug ip ospf hello command is issued on R1. these log messages are seen.
Which command can be configured on routers R1 and R2 on fO/O interfaces to form OSPF adjacency?
- A. ip ospf network point-to- multipoint non-broadcast
- B. ip ospf network broadcast
- C. ip ospf network point-to-point
- D. ip ospf network non-broadcast
Answer: C
NEW QUESTION # 169
A network engineer must enable the helper router to terminate the OSPF graceful restart process if it detects any changes in the LSA. Which command enables this feature?
- A. nsf cisco enforce global
- B. nsf ietf helper disable
- C. nsf ietf helper strict-lsa-checking
- D. nsf Cisco helper disable
Answer: C
NEW QUESTION # 170
Which two actions describe ISP delegation to PCE servers? (Choose two)
- A. adding a new PCE server with higher precedence than the primary PCE
- B. entering the mpls traffic-eng reoptimize command
- C. changing the precedence of any of the PCE servers
- D. adding a new PCE server with lower precedence than the primary PCE
- E. removing TE re-optimization timer timeouts
Answer: C,D
Explanation:
ISP delegation to PCE servers involves assigning specific tasks or roles to different PCE servers within a network. Option A refers to adding a new PCE server with lower precedence than the primary PCE, which means introducing an additional server that has less priority in task execution compared to the existing primary one. Option B involves changing the precedence of any of the PCE servers, indicating a modification in their hierarchical order or priority for task execution. Reference := Cisco Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR)
NEW QUESTION # 171
Refer to the exhibit:
What is the URL used for with REST API?
- A. It is used to send a TACACS+ authentication request to a server
- B. It is used to contact a URL filter to determine the efficacy of a web address
- C. It is used to send a message to the APIC to perform an operation on a managed object or class operator
- D. It is used to initiate an FTP session to save a running configuration of a device.
Answer: C
NEW QUESTION # 172
Refer to the exhibit.
What reestablishes the OSPF neighbor relationship between Router 1 and Router 2?
- A. correct wildcard mask is used on Router 2
- B. OSPF process IDs match
- C. hello intervals match
- D. authentication is added to the configuration
Answer: C
NEW QUESTION # 173
Refer to the exhibit.
A network operator must configure CSR1 interlaces GigabitEihernet2 and GigabitEthemet to rewrite VLAN tags 12 and 21 for traffic between R1 and R2 respectively. Which configurator accomplishes this task?
A)
B)
C)
D)
- A. Option A
- B. Option B
- C. Option C
- D. Option D
Answer: B
NEW QUESTION # 174
Refer to the exhibit.
Guidelines
-
This is a lab item in which tasks will be performed on virtual devices.
* Refer to the Tasks tab to view the tasks for this lab item.
* Refer to the Topology tab to access the device console(s) and perform the tasks.
* Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
* All necessary preconfigurations have been applied.
* Do not change the enable password or hostname for any device.
* Save your configurations to NVRAM before moving to the next item.
* Click Next at the bottom of the screen to submit this lab and move to the next question.
* When Next is clicked, the lab closes and cannot be reopened.
Topology
Tasks
-
R1 and R2 are having issues forming an eBGP neighbor relationship. Troubleshoot and resolve the issue to achieve these goals:
1. Configure R1 and R2 to form a BGP neighborship using their Loopback interfaces.
2. Form the neighbor relationship using a BGP multihop mechanism. Use minimal values to solve the issue.
Answer:
Explanation:
Here is the solution:
NEW QUESTION # 175
Refer to the exhibit.
An engineer is configuring router R1 for OSPFv3 as shown. Which additional configuration must be performed so that the three active interfaces on the router will advertise routes and participate in OSPF IPv6 processes?
- A. C
- B. B
- C. A
Answer: C
NEW QUESTION # 176
Refer to the exhibit.
What type of configuration is it?
- A. It is configuration for the head-end router of a Cisco MPLS TE tunnel with segment routing.
- B. It is configuration that requires OSPF to also be running to have optimized Cisco MPLS TE tunnels.
- C. It is configuration that requires an explicit Cisco MPLS TE path to be configured for the tunnel to run.
- D. It is configuration that requires a dynamic Cisco MPLS TE path to be configured for the tunnel to run.
Answer: A
NEW QUESTION # 177
Refer to the exhibit.
An engineer is configuring multitiopology IS-IS for IPv6 on router R1. Which additional configuration must be applied to complete the task?
A)
B)
C)
- A. Option B
- B. Option A
- C. Option C
- D. Option D
Answer: C
NEW QUESTION # 178
......
Cisco 350-501 (Implementing and Operating Cisco Service Provider Network Core Technologies) certification exam is designed to validate the skills and knowledge of professionals who are responsible for implementing and operating Cisco service provider network solutions. 350-501 exam is intended for individuals who have experience working with Cisco service provider technologies and are looking to enhance their skills and advance their careers.
100% Free 350-501 Daily Practice Exam With 452 Questions: https://www.exam4free.com/350-501-valid-dumps.html
Pass 350-501 Review Guide, Reliable 350-501 Test Engine: https://drive.google.com/open?id=1oF0kN8ap7MJQsb-Vp1gzHb2b9ScNWN6S
