Give Push to your Success with HPE Technical HPE0-S59 Exam Questions
HPE0-S59 100% Guarantee Download HPE0-S59 Exam PDF Q&A
To prepare for the exam, candidates are encouraged to review the HPE0-S59 exam objectives and study materials provided by Hewlett Packard Enterprise. There are also a variety of training courses and certification programs available that can help candidates develop the knowledge and skills necessary to pass the exam. Overall, passing the HP HPE0-S59 exam demonstrates a high level of expertise in HPE compute solutions and can open up new opportunities for IT professionals in the field.
HP HPE0-S59 exam covers a wide range of topics, including HPE compute solutions architecture and technologies, installation, configuration, maintenance, and troubleshooting. HPE0-S59 exam has 60 multiple-choice questions that you need to answer within 120 minutes. The passing score for HPE0-S59 exam is 68%, and it is available in English, Japanese, and Simplified Chinese. By passing the HP HPE0-S59 exam, you will join the elite group of HPE certified professionals, which can enhance your career prospects and job opportunities in the IT industry.
NEW QUESTION # 24
Hotspot Question
Click the port on the Frame Link Module which is used to include an HPE Synergy frame in the management ring.
Answer:
Explanation:
Explanation:
The port labeled "MGMT" (Management) in the upper right section of the HPE Frame Link Module (FLM) is the correct port used to include an HPE Synergy frame in the management ring.
This port is crucial for linking the frame into the management network of the Synergy infrastructure.
NEW QUESTION # 25
Your customer plans to use HPE Primera to boot HPE Synergy compute nodes. They currently have two HPE Virtual Connect SE 100Gb F32 Module for Synergy modules installed in the frame. The customer wants to use FC as a storage access protocol What must be done to complete this task?
- A. Add FC upgrade licenses in HPE OneView that will enable FC connectivity for the modules
- B. Enter both modules into a maintenance mode, then enable FC connectivity through CLI
- C. FC connectivity on the modules should be enabled through the service console by disabling FCoE.
- D. Enable FC primary and secondary boot on the modules through the HPE OneView interface
Answer: D
Explanation:
To use FC (Fibre Channel) as a storage access protocol with HPE Primera to boot HPE Synergy compute nodes, you must add FC upgrade licenses in HPE OneView. These licenses enable FC connectivity for the HPE Virtual Connect SE 100Gb F32 Modules, allowing the compute nodes to connect to the FC storage.
NEW QUESTION # 26
An HPE Synergy customer needs to prevent a timeout and loss of communication during an external switch firmware upgrade.
Click the parameter that the customer should configure within an uplink set to meet this requirement
Answer:
Explanation:
Explanation:
To prevent a timeout and loss of communication during an external switch firmware upgrade, the customer should configure the LACP failover trigger within the uplink set. By setting the LACP failover trigger to "All active uplinks transition to offline," the configuration ensures that the traffic will be redirected to available uplinks in the event of an uplink failure or during the upgrade process, maintaining communication and preventing timeouts.
NEW QUESTION # 27
Your customer plans to expand an existing nPar based on a single HPE Superdome Flex chassis. Which statement about workload availability during expansion is true?
- A. Powered nPar can be expanded if it does not use HPE Persistent Memory
- B. Powered nPar can be expanded only if HPE Superdome Flex 280 is used
- C. Online expansion is available only if RMC is used for management.
- D. HPE Superdome Flex does not support expansion of powered on nPars
Answer: A
Explanation:
HPE Superdome Flex allows for the expansion of powered-on nPars (nPartitions), but this capability is subject to certain conditions. One of these conditions is that the nPar does not use HPE Persistent Memory.
Expanding an nPar with Persistent Memory typically requires a shutdown to reconfigure the memory settings safely.
NEW QUESTION # 28
Hotspot Question
Your customer is implementing an HPE Synergy solution based on three frames. Click each of the ports that can be used to connect satellite modules.
Answer:
Explanation:
NEW QUESTION # 29
Your customer plans to use HPE Primera to boot HPE Synergy compute nodes. They currently have two HPE Virtual Connect SE 100Gb F32 Module for Synergy modules installed in the frame. The customer wants to use FC as a storage access protocol What must be done to complete this task?
- A. Enter both modules into a maintenance mode, then enable FC connectivity through CLI
- B. Add FC upgrade licenses in HPE OneView that will enable FC connectivity for the modules
- C. FC connectivity on the modules should be enabled through the service console by disabling FCoE.
- D. Enable FC primary and secondary boot on the modules through the HPE OneView interface
Answer: B
Explanation:
To use FC (Fibre Channel) as a storage access protocol with HPE Primera to boot HPE Synergy compute nodes, you must add FC upgrade licenses in HPE OneView. These licenses enable FC connectivity for the HPE Virtual Connect SE 100Gb F32 Modules, allowing the compute nodes to connect to the FC storage.
NEW QUESTION # 30
Which statement about the HPE Synergy Image Streamer is true?
- A. Image Streamer is responsible for the configuration of network settings across Synergy frames.
- B. Image Streamer can manage firmware and driver baselines across multiple frames.
- C. Image Streamer can manage OS images, firmware, and drivers across multiple frames.
- D. Image Streamer is used to deploy OS images to the internal disks of compute modules.
Answer: C
NEW QUESTION # 31
Which statement about a new HPE SimpliVity deployment is true?
- A. New HPE SimpliVity deployments are licensed per node not per physical socket
- B. All new HPE SimpliVity models are based on AMD CPUs
- C. All new HPE SimpliVity models support deduplication and compression
- D. New HPE SimpliVity deployments give customer flexible choice of hypervisor
Answer: D
Explanation:
All new HPE SimpliVity models are designed with integrated deduplication, compression, and optimization capabilities. These features are fundamental to the HPE SimpliVity architecture, providing enhanced storage efficiency and performance. Deduplication and compression reduce the amount of data stored and transmitted, which improves the overall efficiency of data management in the hyper-converged infrastructure.
NEW QUESTION # 32
Which statement about login redistribution is true?
- A. Login redistribution is available only If HPE Primera or HPE Alletra is connected directly to the HPE Synergy frame
- B. Login redistribution is a licensed feature and the number of licenses required depends on the number of active ports
- C. Login redistribution is supported only on the HPE Synergy Virtual Connect SE 32Gb FC Modules
- D. Login redistribution is used for login balancing when they are not distributed evenly over the FC links
Answer: D
Explanation:
Login redistribution is a feature that ensures logins are balanced across available FC (Fibre Channel) links.
This process helps maintain optimal performance and redundancy by redistributing logins if they are not evenly distributed. This feature is essential in environments where maintaining balanced load distribution is critical for performance and reliability.
NEW QUESTION # 33
You need to configure a RoCE network to enable lossless networking for HPE J2000 Flash Enclosure support.
Which interconnects are required to support this connection? (Select two.)
- A. HPE Virtual Connect SE 32Gb FC Module for HPE Synergy
- B. Brocade 16Gb Fibfe Channel SAN Switch Module for HPE Synergy
- C. HPE Virtual Connect SE 100Gb F32 Module for HPE Synergy
- D. HPE Virtual Connect SE 16Gb FC Module for HPE Synergy
- E. HPE Virtual Connect SE 40Gb F8 Module for HPE Synergy
- F. Brocade 32Gb Fibre Channel SAN Switch Module for HPE Synergy
Answer: C,E
Explanation:
To configure a RoCE (RDMA over Converged Ethernet) network for HPE J2000 Flash Enclosure support, you need interconnects that support high-bandwidth, low-latency Ethernet connections.
The HPE Virtual Connect SE 40Gb F8 Module and the HPE Virtual Connect SE 100Gb F32 Module for HPE Synergy are suitable choices, as they provide the necessary capabilities for RoCE and lossless networking.
NEW QUESTION # 34
Your customer plans to use HPE OneView for VMware vCenter Server to deploy ESXi systems. They created a server profile template that they want to use in HPE OneView.
Put the steps required to configure HPE OneView for VMware vCenter Server on the left into their correct order on the right.
Answer:
Explanation:
Explanation:
To configure HPE OneView for VMware vCenter Server to deploy ESXi systems, follow these steps in the correct order:
* Add HPE OneView credentials to the vCenter Server and create OS Deployment Plan.
* Add vCenter Server to HPE OneView for VMware vCenter Server.
* Upload HPE-friendly ESXi image.
* Deploy new ESXi systems using vCenter Server interface.
* Add HPE OneView credentials to the vCenter Server and create OS Deployment Plan:Integrate HPE OneView with vCenter Server by adding the necessary credentials and setting up the OS Deployment Plan.
* Add vCenter Server to HPE OneView for VMware vCenter Server:Ensure that vCenter Server is added to HPE OneView for VMware vCenter Server to enable communication and management.
* Upload HPE-friendly ESXi image:Upload an ESXi image that is optimized for HPE hardware to the vCenter Server for use in the deployment process.
* Deploy new ESXi systems using vCenter Server interface:Use the vCenter Server interface to deploy new ESXi systems based on the created server profile template and the uploaded ESXi image.
These steps ensure a seamless deployment and management of ESXi systems using HPE OneView integrated with VMware vCenter Server.
NEW QUESTION # 35
You are troubleshooting an HPE OneView server profile that presents a critical state.
The server profile was configured with a Link Aggregation Group.
What should you check to fix the issue?
- A. if the logical enclosure is configured with redundant master modules
- B. if both FiexNICs are configured with the same speed
- C. if both FiexNICs are connected to different networks
- D. If the logical enclosure is built on at least three HPE Synergy frames
Answer: B
Explanation:
When troubleshooting a server profile in HPE OneView that is in a critical state due to a Link Aggregation Group (LAG), it is important to check if both FlexNICs are configured with the same speed. Inconsistent speeds can cause issues with link aggregation, leading to network instability and performance degradation.
NEW QUESTION # 36
Your customer has the following HPE Synergy setup:
- 15 HPE Synergy 12000 frames with 50Gb connectivity to each server
port
- 2 HPE Composer 2 modules
- 15 HPE D3940 Storage Modules, one per frame
- 2 HPE 12Gb SAS switches per frame
Which statement about this setup is true?
- A. The customer can install up to 12 HPE Synergy 480 compute nodes per frame.
- B. The customer must create at least five logical enclosures for this setup.
- C. If properly cabled, any compute node can access any HPE D3490 storage module
- D. To manage 15 frames, additional HPE Composers are required.
Answer: B
Explanation:
With 15 HPE Synergy 12000 frames, the customer must create multiple logical enclosures to manage the setup efficiently. HPE Synergy typically supports up to five frames per logical enclosure, meaning that at least five logical enclosures would be necessary to manage all 15 frames. This ensures proper organization, management, and scalability of the resources.
NEW QUESTION # 37
Your customer wants to add multiple compute nodes to an existing HPE SimpliVity environment.
Which statement about this expansion is true?
- A. Each compute node will need a capacity-based license that covers a specific amount of memory, CPUs, and storage.
- B. A maximum of five compute nodes per HPE SimpliVity cluster can be added, with no more than 32 sockets in total.
- C. The number of compute nodes that can be added depends on the number and type of HPE SimpliVity nodes.
- D. If a stretched cluster is implemented, an extension must be applied before compute nodes can be added.
Answer: C
NEW QUESTION # 38
What is a limitation when creating a server profile?
- A. Administrator cannot define more than 8 connections within a server profile
- B. BIOS settings can be changed only when UEFI optimized is selected as boot mode
- C. ILO management is limited to the integration with Active Directory or LDAP
- D. It is not possible to create shared volumes on demand through a server profile
Answer: C
NEW QUESTION # 39
Which statement about a new HPE SimpliVity deployment is true?
- A. New HPE SimpliVity deployments are licensed per node not per physical socket
- B. All new HPE SimpliVity models are based on AMD CPUs
- C. New HPE SimpliVity deployments give customer flexible choice of hypervisor
- D. All new HPE SimpliVity models support deduplication and compression
Answer: D
NEW QUESTION # 40
Drag and Drop Question
Match HPE Superdome Flex system with its specific feature.
Answer:
Explanation:
NEW QUESTION # 41
Your customer needs to move an application from an HPE Synergy 480 Gen10 Compute Module to an HPE Synergy 660 Gen 10 Compute Module. The 480 has a switch that has been manually zoned outside of HPE OneView.
What must the customer do before migrating the application?
- A. Copy the server profile and assign the clone to the new hardware
- B. Migrate the application to a Logical JBOD and connect it to the new server
- C. Edit the server profile and change server hardware type
- D. Create a new server profile template and apply to the new hardware
Answer: A
Explanation:
When migrating an application from an HPE Synergy 480 Gen10 Compute Module to an HPE Synergy 660 Gen10 Compute Module, the recommended approach is to copy the server profile and assign the clone to the new hardware. This ensures that all the necessary configuration settings, including network and storage configurations, are retained and applied to the new compute module. Since the switch zoning is manually configured outside of HPE OneView, copying the server profile helps in maintaining consistency in the network settings during the migration.
NEW QUESTION # 42
What is a restriction of using a RoCE network?
- A. it is not supported with HPE Virtual Connect SE 40 GD F8 Module for HPE Synergy.
- B. It does not support smart link and private network features.
- C. It does not support Private VLAN and Multicast VLAN.
- D. It is by default configured as an untagged network and cannot be a part of a network set.
Answer: D
NEW QUESTION # 43
You configured a vVoI datastore using HPE Storage integration Pack for VMware vCenter.
Which storage object should you check using SSMC to verify whether vVol datastore is configured property?
- A. virtual Volume
- B. Virtual Volume Set
- C. Storage Container
- D. App Volume Set
Answer: B
NEW QUESTION # 44
......
HP HPE0-S59 (HPE Compute Solutions) Exam is designed to test the knowledge and skills of individuals when it comes to designing, deploying, and managing HPE compute solutions. HPE0-S59 exam assesses the expertise of candidates in understanding the HPE compute portfolio, identifying the right HPE compute solutions based on customer business needs, and providing technical solutions. HPE Compute Solutions certification is essential for those who are looking to validate their skills in the compute solutions domain and advance their career in the IT industry.
Get HPE0-S59 Actual Free Exam Q&As to Prepare Certification: https://www.exam4free.com/HPE0-S59-valid-dumps.html
HP Actual Free Exam Questions And Answers: https://drive.google.com/open?id=12dMc4LB4chuRd0HWLoU4piYKuYOO0b-X
